Chapter 34
Shoes
A shoe is not drafted on paper from the body. It is built on a last, a solid model of the foot, and its pattern is taken from the last. This chapter explains how; the editor does not draft shoes, because the pattern depends on a last you hold in your hands.
Measuring the foot
- Measure both feet, standing and sitting: the right foot is rarely the same as the left, and a foot spreads and lengthens under the weight of the body.
- Length: trace round the foot standing on paper, the pencil held upright, the toes pressed down; measure from heel to the longest toe.
- Ball girth: round the widest part of the forefoot over the joints of the big and little toes, the tape slightly slanted.
- Instep girth: round the top of the foot, about 6 cm behind the ball.
- Heel girth: from the back of the heel over the front of the ankle bend, the way the foot passes into the shoe.
- Ankle girth, for boots, above the ankle bones.
- A profile traced along the side of the foot, with a heel of the planned height under it, and an inked footprint show the arch.
The foot is about one eighth of the body height. Walking, it lengthens by about 1.5 cm, so the last is made about that much longer than the foot, which keeps the toes off the end of the shoe.
Size systems
| System | One size step | Example |
|---|---|---|
| Paris point (Europe) | 6.67 mm (two thirds of a centimetre) | size 42 = a last of 28 cm |
| English | 8.47 mm (a third of an inch) | size 8 = European 42 |
| American | the English step, counted from a different start | size 9½ = English 8 |
| Metric | the last length in centimetres | 28 = European 42 |
Widths are numbered or lettered separately; within one length a narrow, a medium and a wide foot need different lasts, and a maker may offer more than one width per size.
The last
Lasts are turned from beech, hornbeam or oak, or moulded in plastic, from size tables for ready-made shoes or from the measurements for a made-to-measure pair. A wedge is cut out of the top and hinged so the last can be pulled out of the finished shoe. A made-to-measure last is filed down where the foot is smaller, or built up with layers of leather where it is bigger, then tried in a rough test pair before the real shoes are cut.
Taking the pattern from the last
- Draw the centre line along the top of the last, from the toe to the back of the heel.
- Cover one side of the last with paper or tape, snipping small wedges along the centre line so it lies smooth.
- Draw the style lines on it: the vamp, the quarters, the throat, the topline, the eyelets.
- Lift the cover off and flatten it: this is the half pattern, or the shell. The inside and the outside of the foot differ, so both are taken.
- Add the allowances: the lasting margin pulled under the insole, and the underlays where one piece goes under the next.
- Trace the pattern double for the whole vamp; the leather takes the curve of the last by itself when it is lasted. The lining follows the upper, with its own allowances.
The parts of a shoe
| Upper | Everything above the sole: the vamp over the toes, the quarters at the sides and back, the tongue. |
| Toe puff and counter | Stiffeners between the upper and the lining at the toe and round the heel. |
| Lining | Soft calf, vegetable tanned so the foot can breathe. |
| Insole | The leather layer the upper is lasted to, under the foot. |
| Welt | A strip of leather about 2 cm wide sewn round the edge of the insole and upper, to which the sole is stitched. |
| Shank | A strip of steel about 10 cm long under the arch, from the middle of the heel forward, so the back of the shoe stays rigid while the front bends. |
| Filler | Cork in the cavity between the insole and the sole. |
| Sole and heel | The sole in leather or rubber; the heel built up of layers with a rubber top piece. |
Main styles
| Oxford | Closed lacing: the quarters are sewn under the vamp. Usually five pairs of eyelets. |
| Derby | Open lacing: the quarters are sewn on top of the vamp and can open wide. |
| Brogue | Either of them with decorative punching along the edges and the toe cap. |
| Monk | Closed with a strap and buckle. |
| Loafer and moccasin | Slip-ons. A true moccasin wraps one piece of leather under the foot and up the sides. |
| Court shoe | A woman’s low-cut shoe without fastening, on a heel. |
| Boots | Ankle, mid-calf or knee high; the leg is usually cut in several pieces. |
How a shoe is made
- Cut the upper from the best part of the hide, the vamp nearest the spine, the left and right shoes from matching places.
- Skive the edges, mark the joins and punch the decorations.
- Glue and stitch the upper together, then the lining, and join them along the topline.
- Insert the toe puff and counter, and last the upper over the last onto the insole.
- Sew the welt, fit the shank and the cork filler, and stitch on the sole.
- Build and attach the heel, trim, dye and burnish the edges, and finish the inside.
A pattern drafted to your body
Pick a garment, type your measurements and print it at home. The T-shirt and the A-line skirt are free to print, and your first PDF of any other pattern is free.
Choose a patternGet new patterns and chapters by e-mail
About once a month. We send a link to confirm, which also opens a free account.