The course

Chapter 14

The shirt

Every number below follows the size you pick.

A shirt is a woven top with a yoke across the shoulders, a buttoned front, a cuff on every sleeve and a collar on a separate stand.

It is drafted on the same principles as the T-shirt: a frame from the chest and the length, the armhole and the shoulder shaped inside it, a sleeve made to fit the armhole. Woven fabric does not stretch, so the shirt gets far more ease than a knit top.

What you need

MeasurementWhere the tape goesSize 50
ChestRound the fullest part of the chest, under the arms and across the shoulder blades. Breathe normally.100.0 cm
SeatRound the fullest part of the seat, feet together.102.0 cm
NeckRound the base of the neck, over the prominent bone at the back and just above the collarbones at the front.39.4 cm
Arm lengthFrom the shoulder point over a slightly bent elbow to the wrist bone.64.0 cm
BicepRound the fullest part of the upper arm, arm relaxed.33.0 cm
WristRound the wrist over the wrist bone.17.5 cm

Draft the shirt to your measurementsFree to draft, your first PDF free

Front.
Back.

How it is drafted

  • Back and yoke. The top of the back is cut off as a yoke and sewn on again across the shoulders. The yoke is cut twice, outside and inside, and the seams are hidden between them.
  • Front. The front gets an extension at the centre for the buttons and buttonholes.
  • Sleeve and cuff. The sleeve is drafted to the armhole and narrowed to the cuff; the cuff is a band that closes round the wrist with a button.
  • Collar. The stand follows the neckline exactly and the collar is drawn on top of it, so the collar turns over the stand.

The finished pieces

BACKFRONTYOKESLEEVECOLLAR
Shirt, size 50. Back (1× on fold), Front (2×), Yoke (2× on fold), Sleeve (2×), Cuff (4×), Collar stand (2× on fold), Collar (2× on fold). Seam allowance is added afterwards.
Before you cut. The yoke seam on the back and on the fronts, the side seams and the sleeve cap against the armhole must match. The editor shows every pair in its fit checks.

Sewing it

  1. Cut and mark. Cut every piece with the grain arrow parallel to the selvedge. Transfer the notches and the marks with tailor's chalk or a short snip into the seam allowance.
  2. Interfacing. Fuse interfacing to the collar, stand, cuffs, waistband, facings and front edges before sewing anything.
  3. Yoke. Sandwich the back between the two yoke layers and stitch; roll the fronts inside to sew the yoke to the front shoulders the same way.
  4. Button stands. Fold and press the button stands on both fronts and stitch them down.
  5. Shoulders. Sew the shoulder seams, the back eased onto the front. Press open.
  6. Collar. Make up the collar, turn and press, then sandwich it in the stand. Sew the stand to the neckline and close it from the outside.
  7. Sleeves. Ease the sleeve cap with two rows of long stitches and sew the sleeve into the open armhole flat, matching the notches.
  8. Side seams. Sew the side seams and the sleeve underarm seams in one line, from the hem to the sleeve end.
  9. Cuffs. Finish the sleeve plackets, pleat the sleeve hem to fit and attach the cuffs.
  10. Hem. Turn up the hem twice and stitch, or catch it by hand.
  11. Buttons. Mark and sew the buttonholes, then the buttons opposite them.
Make it

Draft the shirt to your measurements

The editor draws this pattern for your body in a few seconds, with seam allowance, notches and sewing steps. Your first PDF is free.

Open the shirt
New chapters

Get new patterns and chapters by e-mail

About once a month. We send a link to confirm, which also opens a free account.