The course

Chapter 15

The tailored jacket

Every number below follows the size you pick.

A tailored jacket is built from a back, a side panel and a front, a two-piece sleeve and a lapel that rolls over the chest.

Three panels instead of two let the jacket follow the waist and the seat without darts showing on the front. The sleeve is cut in two pieces, a topsleeve and an undersleeve, so it curves forward like the arm.

What you need

MeasurementWhere the tape goesSize 50
ChestRound the fullest part of the chest, under the arms and across the shoulder blades. Breathe normally.100.0 cm
WaistRound the natural waist, where the body is narrowest, usually just above the navel.88.0 cm
SeatRound the fullest part of the seat, feet together.102.0 cm
Arm lengthFrom the shoulder point over a slightly bent elbow to the wrist bone.64.0 cm
BicepRound the fullest part of the upper arm, arm relaxed.33.0 cm

Draft the tailored jacket to your measurementsFree to draft, your first PDF free

Watch it drafted

The whole draft, one step at a time. Press play, or step through with the arrows.

1
Step 1 of 37
Back, side panel and frontNape and centre back line
start of the draft

Drafting, step by step

Each picture shows everything drawn so far; the new line of the step is in colour. The formulas show the names of the measurements first, then the numbers for size 50.

  1. 1

    Back, side panel and front

    Step 1

    Nape and centre back line

    start of the draft

    The whole body of the jacket is drafted in one drawing: back on the left, side panel in the middle, front on the right. Every depth is measured down from the nape, point 1.

  2. 12

    Step 1–2

    Chest line

    Chest ÷ 8 + 12.0 + armhole depth adjust
    = 100.0 ÷ 8 + 12.0 + 0.0 = 24.5 cm

    The chest line is the depth of the armhole. It is drawn square to the centre back across the whole block, because the back, the side panel and the front all start from it.

  3. 123

    Step 1–3

    Waist line

    Height ÷ 4 + 1.0
    = 182.0 ÷ 4 + 1.0 = 46.5 cm

    The waist line places the suppression of the side seams and the buttons.

  4. 1234

    Step 3–4

    Hip line

    Height ÷ 8
    = 182.0 ÷ 8 = 22.8 cm

    The hip line sits an eighth of the height below the waist; the jacket is checked against the hip there.

  5. 12345

    Step 1–5

    Jacket length

    Height ÷ 2 − 11.5 + length adjust
    = 182.0 ÷ 2 − 11.5 + 0.0 = 79.5 cm

    The length is half the height − 11.5, measured down the centre back from the nape.

  6. 123456

    Step 2–6

    Back width

    Chest × 2 ÷ 10 + 1.3
    = 100.0 × 2 ÷ 10 + 1.3 = 21.3 cm

    The chest line is divided into three widths: back, armhole and front. Each is a proportion of the chest with the ease already in it. The back width line goes up from point 6 to the shoulder.

  7. 1234567

    Step 6–7

    Armhole width

    Chest ÷ 8 + 4.0
    = 100.0 ÷ 8 + 4.0 = 16.5 cm

    The armhole width is the room for the arm between the back and the front. The line before the armhole goes up from point 7.

  8. 12345678

    Step 7–8

    Front width

    Chest × 2 ÷ 10 + 1.5
    = 100.0 × 2 ÷ 10 + 1.5 = 21.5 cm

    Point 8 is the centre front on the chest line. Check: the three widths together are 59.3, half the chest is 50.0, so the ease in half the jacket is 9.3.

  9. 123456789

    Step 1–9

    Centre back

    centre back suppression = 0.8

    The back follows the spine: straight over the shoulder blades, then in at the waist and out again over the seat. Point 9 is the centre back at the waist.

  10. 12345678910

    Step 1–10

    Back neck

    Chest ÷ 2 ÷ 10 + 3.0 + neck width adjust
    = 100.0 ÷ 2 ÷ 10 + 3.0 + 0.0 = 8.0 cm

    The back neck width is a tenth of half the chest + 3.0; the neck point is raised 1.5 cm above the nape and joined to it in a shallow curve. Point 10 is the back neck point.

  11. 1234567891011

    Step 10–11

    Back shoulder

    shoulder extension + shoulder pad lift
    = 0.0 + 1.0 = 16.4 cm

    The shoulder runs from the neck point through a point 2.0 cm below the top of the back width line and goes 2.0 cm beyond it, so the shoulder reaches the end of the shoulder bone.

  12. 1234567891011

    Step 12

    Front shoulder height

    the front top line 2.3 above the chest depth of the back: 2.3 cm

    The front is taken higher than the back, because the front of the body is longer from the shoulder to the chest line. The top line of the front is square to the centre front.

  13. 123456789101113

    Step 12–13

    Front neck

    Chest ÷ 2 ÷ 10 + 3 + 2
    = 100.0 ÷ 2 ÷ 10 + 3 + 2 = 12.8 cm

    The front neck point 13 sits back from the centre front by the back neck width plus 2. The neckline goes down from it to the centre front.

  14. 12345678910111314

    Step 13–14

    Front shoulder

    towards 4.0 cm down on the line before the armhole, 0.8 shorter than the back: 15.3 cm

    The back shoulder is eased onto the front, which gives room over the shoulder blades.

  15. 12345678910111314bpfp

    Step 11–14

    Armhole

    back pitch a quarter of the chest depth above the chest line, front pitch a quarter of the armhole width less 1: 57.5 cm

    The armhole touches the back width line at the back pitch and the line before the armhole at the front pitch, and goes down to the chest line between them. Its length sets the sleeve cap.

  16. 12345678910111314bpfp15

    Step 8–15

    Centre front

    Waist ÷ 4 + 0.25
    = 88.0 ÷ 4 + 0.25 = 22.3 cm

    At the waist the front is as wide as a quarter of the waist plus ease, or as the chest width when that is wider, so it covers the stomach. The front is 1.2 cm longer than the back at the hem.

  17. 12345678910111314bpfp15

    Step 16

    Back side seam

    side waist suppression = 1.8

    The seam between the back and the side panel starts at the back pitch and goes in at the waist by the side suppression, then out to the hip.

  18. 12345678910111314bpfp15

    Step 17

    Side panel

    side panel front suppression = 1.5

    The seam between the side panel and the front leaves the armhole 2.5 cm in front of the line before the armhole and is suppressed at the waist. Back and front seams of the side panel are spread at the hip until the hip width with ease is reached.

  19. 12345678910111314bpfp15

    Step 18

    Hip width

    (Seat + hip ease) ÷ 2
    = (102.0 + 9.0) ÷ 2 = 55.5 cm

    The hip line is checked last: what is still missing is added at the side panel seams, shared between back and front.

  20. 12345678910111314bpfp15b

    Step 19

    Buttons and break point

    button extension = 2.0

    The buttons sit on the centre front and the edge is the extension beyond it. The lapel starts to roll at the break point above the top button.

  21. 12345678910111314bpfp15b20

    Step 13–20

    Roll line

    from 2 cm along the shoulder past the neck point to the break point: 47.3 cm

    The lapel folds back along the roll line. It starts on the shoulder line 2 cm beyond the neck point, where the collar stand begins.

  22. 12345678910111314bpfp15b2021

    Step 21

    Lapel and gorge

    lapel width = 9.5

    The lapel is drawn on the front as it will lie when folded: its width is taken square to the roll line, and the gorge line where the collar joins it sets the notch.

  23. 12345678910111314bpfp15b2021

    Step 22

    Pockets

    the front length from the top line to the hem in thirds: breast welt 11 at the upper third less 1, flap pocket 17 × 6 at the lower third less 1: 27.7 cm

    Dividing the front length in thirds puts the pockets in proportion with the jacket at every size.

  24. 12345678910111314bpfp15b2021

    Step 23

    Front dart

    front dart = 2.0

    The front dart takes in the waist under the chest; its end is hidden in the opening of the flap pocket.

  25. 12345678910111314bpfp15b2021

    Step 25

    Outline of the back

    The back with its centre back vent.

  26. 12345678910111314bpfp15b2021

    Step 26

    Outline of the side panel

    The side panel between the back and the front.

  27. 12345678910111314bpfp15b2021

    Step 27

    Outline of the front

    The front with the lapel, the dart and the pocket marks.

  28. Two-piece sleeve

    Step 1

    Armhole height

    back and front, from the shoulder points to the chest line: 45.4 cm

    The sleeve is drafted from the armhole of the body: its height and its length measured on the draft.

  29. 2

    Step 1–2

    Cap height

    half the armhole height − (armhole height ÷ 20 + 1.5): 18.9 cm

    A cap of this height lets the arm lift without pulling, and gives a sleeve that hangs straight.

  30. 2

    Step 2–3

    Sleeve length

    Arm length − shoulder extension + 1.5
    = 64.0 − 0.0 + 1.5 = 65.5 cm

    Measured from the top of the cap down the topsleeve.

  31. 2

    Step 4

    Cap ease

    cap ease = 3.5

    The cap is a little longer than the armhole and eased in as the sleeve is set, so it rounds over the shoulder.

  32. 2

    Step 5

    Sleeve hem

    sleeve hem width = 32.0

    The topsleeve is wider and lies over the arm; the undersleeve is narrower and hidden underneath. Both seams curve forward at the elbow like the arm.

  33. 2

    Step 33

    Outline of the topsleeve

    The topsleeve.

  34. 2

    Step 34

    Outline of the undersleeve

    The undersleeve, drawn on the same lines.

  35. Collar

    Step 1

    Collar neck seam

    gorge + front neck + back neck − 1, the back part along the roll line carried on, 1.5 square to it: 26.0 cm

    The under collar is drawn on the front: along the gorge, round the front neck, then on along the roll line by the back neck length less 1 cm and 1.5 cm square to it, so the collar seam is about 1 cm shorter than the neck and hugs it.

  36. Step 2

    Stand and fall

    collar stand + collar fall
    = 2.5 + 4.2 = 6.7 cm

    The stand rises from the neck; the fall turns over it and covers the neck seam.

  37. Step 37

    Outline of the under collar

    The under collar. The top collar is cut from the same shape with a little more at the outer edge.

The finished pieces

BACKSIDE PANELFRONTTOPSLEEVEUNDERSLEEVEUNDER COLLARFRONT FACINGBACK LININGSIDE PANEL LININGFRONT LININGTOPSLEEVE LININGUNDERSLEEVE LININGPOCKET BAG
Tailored jacket, size 50. Back (2×), Side panel (2×), Front (2×), Topsleeve (2×), Undersleeve (2×), Under collar (2×), Pocket flap (4×), Front facing (2× (+ 2× interfacing)), Back neck facing (2× (+ 2× interfacing)), Back lining (2× lining), Side panel lining (2× lining), Front lining (2× lining), Topsleeve lining (2× lining), Undersleeve lining (2× lining), Piping strip (2×), Pocket bag (4× lining). Seam allowance is added afterwards.
Sew a toile first. A jacket has many seams that must meet. A quick version in cheap fabric shows the fit at the shoulders, the lapel and the sleeve before you cut wool.

Sewing it

  1. Cut and mark. Cut every piece with the grain arrow parallel to the selvedge. Transfer the notches, the dart points and the marks with tailor's chalk or a short snip into the seam allowance.
  2. Interfacing. Fuse interfacing to the collar, stand, cuffs, waistband, facings and front edges before sewing anything.
  3. Darts. Sew each dart from the wide end to the point, the last stitches right on the fold. Tie the threads at the point, do not backstitch. Press waist darts towards the centre, bust darts downwards.
  4. Pockets. Make the pockets and flaps and set them on the fronts while the pieces are flat.
  5. Panels. Join the side panels to the back and the front, matching the notches. Press the seams open over a tailor's ham.
  6. Shoulders. Sew the shoulder seams, the back eased onto the front. Press open.
  7. Side seams. Sew the side seams, matching the notches. Press open.
  8. Collar and facings. Sew the facings to the fronts, the under collar to the neckline and the top collar to the facings; turn, roll and press the lapels and collar into shape.
  9. Sleeves. Sew the two sleeve seams, ease the cap with two rows of long stitches and set the sleeves into the armholes, matching the notches. Add a sleeve head and shoulder pads if used.
  10. Lining. Sew the lining like the shell: darts, panels, shoulders, side seams and sleeves, leaving 20 cm open in one sleeve seam. Fold the pleat at the centre back and baste it at the neck and the hem. Sew the lining to the inner edge of the facings, right sides together, matching the notches. Join it to the hems of the body and the sleeves about 1.5 cm above its own edge, so a small fold of ease stays at the hem, then turn the garment through the opening and close it.
  11. Hem. Turn up the hems, catch them by hand and bag the lining in if the garment is lined.
  12. Buttons. Mark and sew the buttonholes, then the buttons opposite them.
Make it

Draft the tailored jacket to your measurements

The editor draws this pattern for your body in a few seconds, with seam allowance, notches and sewing steps. Your first PDF is free.

Open the tailored jacket
New chapters

Get new patterns and chapters by e-mail

About once a month. We send a link to confirm, which also opens a free account.