The course

Chapter 26

The cape

Every number below follows the size you pick.

A cape is drafted from the shoulders of a loose coat: the front and the back are laid side by side and joined into one piece.

How far the back is swung away from the front decides the fullness: a half circle, three quarters or a full circle.

What you need

MeasurementWhere the tape goesSize 38
BustRound the fullest part of the bust, level all round, under the arms. Wear the bra the garment will be worn with.88.0 cm
Back length (nape to waist)Down the centre back, from the prominent bone at the base of the neck to the waist. Tie a string round the waist to find it.40.6 cm
Front length (neck point to waist)From the side of the neck, over the bust point, straight down to the waist.45.0 cm
Shoulder lengthFrom the side of the neck to the shoulder point, the bone at the end of the shoulder.12.2 cm
Shoulder to shoulderAcross the back from one shoulder point to the other, over the base of the neck.37.2 cm
NeckRound the base of the neck, over the prominent bone at the back and just above the collarbones at the front.36.6 cm
Arm lengthFrom the shoulder point over a slightly bent elbow to the wrist bone.60.0 cm

Draft the circular cape to your measurementsFree to draft, your first PDF free

Watch it drafted

The whole draft, one step at a time. Press play, or step through with the arrows.

Step 1 of 13
CapeFront frame
(Bust + bust ease (loose coat)) ÷ 4
= (88.0 + 18.0) ÷ 4 = 26.5 cm

Drafting, step by step

Each picture shows everything drawn so far; the new line of the step is in colour. The formulas show the names of the measurements first, then the numbers for size 38.

  1. Cape

    Step 1

    Front frame

    (Bust + bust ease (loose coat)) ÷ 4
    = (88.0 + 18.0) ÷ 4 = 26.5 cm

    The cape is built on a loose coat base without darts. Its front is drawn first, from the centre front; the side line is in the middle of the half frame.

  2. UU1

    Step 2

    Front neck

    half shoulder width ÷ 3
    = 21.4 ÷ 3 = 7.1 cm

    The neck point is a third of the half shoulder width from the centre front, and the base neck is as deep as it is wide. The half shoulder width is half the shoulder-to-shoulder measure with 4.5 ease, plus 0.5. Under the hood the neckline runs down to the chest line on the centre front.

  3. UU1VZ

    Step 3

    Front shoulder

    Shoulder length + 2 − 0.5
    = 12.2 + 2 − 0.5 = 13.7 cm

    The shoulder slopes from the neck point towards a point 6 cm down the side line.

  4. UU1VZP1D

    Step 4

    Back

    the back laid square to the front, the shoulder points 2 apart: 2.0 cm

    The back of the same base (neck point a third of the half shoulder width + 1 from the centre and 2.5 up, shoulder + 2 long) is laid against the front. How far it is swung open decides how full the cape is.

  5. UU1VZP1DU3P2

    Step 5

    Neck widened

    neckline widened at the shoulder = 2.5

    A cape is worn over other clothes, so the neckline is opened along the shoulders.

  6. UU1VZP1DU3P2RR1

    Step 6

    Shoulder seam

    from the widened neck points to a point 3.5 beyond the middle of the shoulder ends: 3.5 cm

    The two shoulders meet in one point beyond the shoulder ends: the wedge between them is the shoulder seam that shapes the cape over the shoulder.

  7. UU1VZP1DU3P2RR1ST

    Step 7

    Hem

    from hem to hem at the side lines; 5 in at the shoulder line: 5.0 cm

    The hem keeps the side length as its reference. Over the shoulder it comes in 5 cm so it hangs level.

  8. UU1VZP1DU3P2RR1ST

    Step 8

    Front edge

    front overlap = 3.0

    The fronts lap over each other for the fastening.

  9. UU1VZP1DU3P2RR1ST

    Step 9

    Outline of the cape

    The cape, cut twice with a centre back seam.

  10. Ua

    Hood

    Step 1

    Neck edge

    the front neckline, then the back neck rising 3: 31.5 cm

    The hood is built on the front: its neck edge is the cape's front neckline down to the chest line, carried on by the length of the back neck.

  11. Ua

    Step 2

    Frame

    hood width × hood height
    = 34.0 × 40.0 = 34.0 cm

    The frame gives the depth of the hood from the face to the back of the head, and its height.

  12. Uabc

    Step 3

    Top and front edge

    the back corner rounded; the top 4 lower at the front over the last 9; the front edge straight to the centre front: 4.0 cm

    The zip runs along the top. Closed, it makes the hood; open, the hood lies flat as a wide collar.

  13. Uabc

    Step 13

    Outline of the hood

    The hood, cut twice, with its lining.

The finished pieces

CAPEHOOD
Circular cape, size 38. Cape (2× (centre back seam)), Hood (2× (+ 2× lining)), Front facing (2× (+ 2× interfacing)). Seam allowance is added afterwards.

Sewing it

  1. Cut and mark. Cut every piece with the grain arrow parallel to the selvedge. Transfer the notches and the marks with tailor's chalk or a short snip into the seam allowance.
  2. Interfacing. Fuse interfacing to the collar, stand, cuffs, waistband, facings and front edges before sewing anything.
  3. Centre back. Sew the centre back seam of the cape.
  4. Shoulders. Sew the shoulder seams from the neck to the shoulder point and press them open.
  5. Hood. Sew the hood centre back seam, turn the face edge in twice and stitch. Sew the hood to the neckline, matching the centre backs.
  6. Front edges. Sew the front facings to the front edges from the neck to the hem, understitch, turn and press; catch the inner edge of the facing down by hand. Set the fastening on the overlap.
  7. Hem. Let the cape hang for a day, level the hem, then turn up a narrow hem or bind it.
Make it

Draft the circular cape to your measurements

The editor draws this pattern for your body in a few seconds, with seam allowance, notches and sewing steps. Your first PDF is free.

Open the circular cape
New chapters

Get new patterns and chapters by e-mail

About once a month. We send a link to confirm, which also opens a free account.