Chapter 20
The overcoat
Every number below follows the size you pick.
An overcoat is drafted to go over a jacket or a jumper: longer, wider and with more ease everywhere than a jacket.
The construction follows the jacket chapter: notch lapels, three buttons, flap pockets and a two-piece sleeve, with a full lining. The extra ease is what lets it go on over other clothes and still close.
What you need
| Measurement | Where the tape goes | Size 50 |
|---|---|---|
| Chest | Round the fullest part of the chest, under the arms and across the shoulder blades. Breathe normally. | 100.0 cm |
| Waist | Round the natural waist, where the body is narrowest, usually just above the navel. | 88.0 cm |
| Seat | Round the fullest part of the seat, feet together. | 102.0 cm |
| Arm length | From the shoulder point over a slightly bent elbow to the wrist bone. | 64.0 cm |
| Bicep | Round the fullest part of the upper arm, arm relaxed. | 33.0 cm |
Draft the overcoat to your measurementsFree to draft, your first PDF free
How it is drafted
- Ease for the layers underneath. The chest, the armhole and the sleeve are larger than in a jacket for the same body.
- Back and front. Two body pieces instead of the jacket's three; the front is extended for the buttons and folds back as the lapel.
- Two-piece sleeve. A topsleeve and an undersleeve, drafted to the deeper armhole.
- Inside. Facings, a full lining and pocket bags, drafted from the same pieces.
The finished pieces
Sewing it
- Cut and mark. Cut every piece with the grain arrow parallel to the selvedge. Transfer the notches, the dart points and the marks with tailor's chalk or a short snip into the seam allowance.
- Interfacing. Fuse interfacing to the collar, stand, cuffs, waistband, facings and front edges before sewing anything.
- Darts. Sew each dart from the wide end to the point, the last stitches right on the fold. Tie the threads at the point, do not backstitch. Press waist darts towards the centre, bust darts downwards.
- Pockets. Make the pockets and flaps and set them on the fronts while the pieces are flat.
- Panels. Join the side panels to the back and the front, matching the notches. Press the seams open over a tailor's ham.
- Shoulders. Sew the shoulder seams, the back eased onto the front. Press open.
- Side seams. Sew the side seams, matching the notches. Press open.
- Collar and facings. Sew the facings to the fronts, the under collar to the neckline and the top collar to the facings; turn, roll and press the lapels and collar into shape.
- Sleeves. Sew the two sleeve seams, ease the cap with two rows of long stitches and set the sleeves into the armholes, matching the notches. Add a sleeve head and shoulder pads if used.
- Lining. Sew the lining like the shell: darts, panels, shoulders, side seams and sleeves, leaving 20 cm open in one sleeve seam. Fold the pleat at the centre back and baste it at the neck and the hem. Sew the lining to the inner edge of the facings, right sides together, matching the notches. Join it to the hems of the body and the sleeves about 1.5 cm above its own edge, so a small fold of ease stays at the hem, then turn the garment through the opening and close it.
- Hem. Turn up the hems, catch them by hand and bag the lining in if the garment is lined.
- Buttons. Mark and sew the buttonholes, then the buttons opposite them.
Make it
Draft the overcoat to your measurements
The editor draws this pattern for your body in a few seconds, with seam allowance, notches and sewing steps. Your first PDF is free.
Open the overcoatNew chapters
Get new patterns and chapters by e-mail
About once a month. We send a link to confirm, which also opens a free account.