The course

Chapter 19

The hoodie

Every number below follows the size you pick.

A hoodie is a loose knit top with a dropped shoulder, a hood and rib bands at the cuffs and the hem.

It starts like the T-shirt, from the chest, the length and the neck, with much more ease. The shoulder is extended past the body, so the armhole sits lower on the arm and the sleeve cap is flatter.

What you need

MeasurementWhere the tape goesSize 50
ChestRound the fullest part of the chest, under the arms and across the shoulder blades. Breathe normally.100.0 cm
NeckRound the base of the neck, over the prominent bone at the back and just above the collarbones at the front.39.4 cm
Nape to waistDown the centre back, from the prominent bone at the base of the neck to the waist. Tie a string round the waist to find it.45.0 cm
Shoulder lengthFrom the side of the neck to the shoulder point, the bone at the end of the shoulder.15.0 cm
Arm lengthFrom the shoulder point over a slightly bent elbow to the wrist bone.64.0 cm
WristRound the wrist over the wrist bone.17.5 cm
SeatRound the fullest part of the seat, feet together.102.0 cm

Draft the hoodie to your measurementsFree to draft, your first PDF free

Front.
Back.

How it is drafted

  • Dropped shoulder. The shoulder line runs past the shoulder point and the armhole is drawn lower and straighter.
  • Hood. The hood is drafted from the neckline of the back and the front, so its edge fits the neck exactly.
  • Rib bands. Cuffs and the hem band are cut shorter than the edges they are sewn to and stretched as they are sewn.
  • Kangaroo pocket. One pocket across the front, cut on the fold.

The finished pieces

BACKFRONTSLEEVEHOODHEM BANDCUFFKANGAROO POCKET
Hoodie, size 50. Back (1× on fold), Front (1× on fold), Sleeve (2×), Hood (2×), Hem band (1×), Cuff (2× rib), Kangaroo pocket (1× on fold). Seam allowance is added afterwards.

Sewing it

  1. Cut and mark. Cut every piece with the grain arrow parallel to the selvedge. Transfer the notches, the dart points and the marks with tailor's chalk or a short snip into the seam allowance.
  2. Set up for stretch. Use a ballpoint or stretch needle and a narrow zigzag or the stretch stitch, or an overlocker. Seams in knit must stretch with the fabric.
  3. Darts. Sew each dart from the wide end to the point, the last stitches right on the fold. Tie the threads at the point, do not backstitch. Press waist darts towards the centre, bust darts downwards.
  4. Pockets. Make the pockets and flaps and set them on the fronts while the pieces are flat.
  5. Shoulders. Sew the shoulder seams; stabilise them with clear elastic or a strip of tape so they do not stretch.
  6. Hood. Sew the hood centre seam, finish the face edge and sew the hood to the neckline.
  7. Sleeves. Sew the sleeves into the open armholes flat, stretching nothing.
  8. Side seams. Sew the side seams and the sleeve underarm seams in one line, from the hem to the sleeve end.
  9. Cuffs. Join the cuffs into rings, fold and sew them to the sleeve ends.
  10. Hem band. Join the band into a ring and sew it to the hem, stretching it evenly.
Make it

Draft the hoodie to your measurements

The editor draws this pattern for your body in a few seconds, with seam allowance, notches and sewing steps. Your first PDF is free.

Open the hoodie
New chapters

Get new patterns and chapters by e-mail

About once a month. We send a link to confirm, which also opens a free account.