The course

Chapter 28

Hats and caps

A hat is drafted from one measurement, the head girth, and fitted to the millimetre. Everything else (how high, how wide the brim) is design.

Head girthRound the head from temple to temple, over the back of the head and across the forehead about 1 cm below the hairline. Head upright, hair loose, nothing in the hair.

Size and fit

  • The hat size is the head girth in centimetres: an adult range of 52 to 60, children from about 45. Letter sizes from XS to XL each cover about two of these numbers.
  • The head line of the hat is the head girth plus a little ease, half a centimetre to one centimetre, more for thick fabrics or a lined crown.
  • A classic hat rests on the top of the forehead and stands clear of the hair by about two centimetres. One that is slightly too big slips down; it is corrected with a strip of tape or felt behind the sweatband until it sits right.

The parts

CrownThe upper part, flat, domed or creased, of any height. Sewn hats build it from a top and a side band, from gores, or from panels.
BrimThe ring sewn to the bottom of the crown. It can be even, wider at the front, turned up, turned down, or both.
BandA ribbon round the bottom of the crown that covers the seam, often finished with a flat bow at the left side.
LiningFixed inside the crown.
SweatbandA strip of leather or grosgrain inside the head line, in direct contact with the head.
PeakThe short stiff crescent at the front of a cap.

Felt and straw are blocked, not drafted

A felt or straw hat has no pattern. Felt is made by matting fur or wool fibres with heat, moisture and pressure into a cone; the cone is dyed, steamed and stretched over a wooden head block for the crown and onto a flat wooden ring for the brim, dried in shape, then trimmed and finished. Straw is plaited into long braids that are sewn in a spiral, or bought as a woven cone, and shaped on a block the same way. These hats need the blocks, so they are not in the editor.

How sewn hats are drafted

  • The head line first. Every piece is measured from it: the band or the crown is as long as the head line at its lower edge, the brim has the head line as its inner edge, and the top is sized to the upper edge of the band.
  • An oval top. Heads are longer than they are wide, so the top of a crown is an ellipse, about 15 by 18 cm for an average head, scaled with the size.
  • A brim as a ring. A flat ring gives a flat brim. Cut a wedge out of the ring at the back and close it, and the brim slopes down; the wider the wedge, the steeper the slope. The inner radius is the head line plus the wedge, divided by 2π.
  • Gores and panels. A crown of four, six or eight gores divides the head line into equal bases; the sides of each gore curve out a little so the crown rounds instead of forming a pyramid.
  • A peak is a crescent: its inner edge follows the front of the head line, its outer edge stands out a few centimetres at the centre and returns to nothing at the ends. The under peak is cut smaller so the seam rolls out of sight.
TOPSIDE BANDBRIMLINING BANDLINING TOP
Bucket hat. Top (1× + 1× lining), Side band (1× on fold + 1× lining on fold), Brim (2× (upper and under) + 1× stiffening), Lining band (1× lining on fold), Lining top (1× lining), Sweatband (1× leather or grosgrain).
PEAK
Six-panel cap. Front and side panel (4× + 4× lining), Back panel (2× + 2× lining (mirrored)), Peak (2× + 1× stiffening), Inside band (1× cotton tape), Back strap (2× (one with the buckle)).

The hats in the editor

Make one

A pattern drafted to your body

Pick a garment, type your measurements and print it at home. The T-shirt and the A-line skirt are free to print, and your first PDF of any other pattern is free.

Choose a pattern
New chapters

Get new patterns and chapters by e-mail

About once a month. We send a link to confirm, which also opens a free account.