The course

Chapter 32

Bags

A bag is drafted from three numbers: its width, its height and its depth. No body measurement is needed, and every piece follows from those three.

The parts

Front and backThe two faces. Often the same piece; on a flap bag the back continues into the flap.
GussetThe strip that gives the depth, running down the sides and under the bottom. Some bags have a separate bottom instead, or box corners cut into the panels.
FlapThe cover that closes over the top, with its own lining.
FacingA band of the outer material inside the top edge, so the lining does not show.
LiningThe inner bag, usually with a zipped pocket.
Handles and strapsFlat and stitched, tubular with a cord inside, braided, or cut out of the panel.
Tabs and fittingsLeather tabs round rings, keepers, buckles, snap hooks, magnets, locks and feet.
StiffeningBoard, foam or interfacing that holds the shape.

Mounting: how the pieces are joined

Edge workThe pieces are glued wrong sides together and stitched close to the edge; the raw edges are bevelled, burnished and dyed. Firm, clean, for thick leather.
TurnedSewn right sides together and turned through, so the seams are inside. Soft bags in thin leather or fabric.
BoundSewn wrong sides together, the edge covered with a strip of leather folded over it and stitched. Semi-rigid bags.
PipedA narrow strip wrapped round a cord is caught in the seam and stands out along it. It strengthens and defines the edge.
ExpandableA pleated or chained strip lets a gusset open wider.

Drafting from width, height and depth

  • The panel is a rectangle of the width by the height, the lower corners rounded as wanted.
  • The gusset is as wide as the depth and as long as the edge of the panel it is sewn round: measure the sides and bottom along the curve. It can taper towards the top.
  • Box corners replace the gusset: add the depth to the width and half the depth to the height, and cut a square of half the depth out of each lower corner. Closing the cut-outs makes the corners.
  • A flap bag has the back and the flap in one: the height of the back, plus the depth across the top, plus the length of the flap.
  • The facing is the top of the panel, five to ten centimetres deep; the lining is the rest of the panel, so the two together make the inside.
  • The lining is cut a little smaller than the outside so it does not wrinkle inside, and carries a zipped pocket somewhat narrower than the panel.
BACK AND FLAPBACK AND FLAP LININGFRONTINNER ZIP POCKET LINING
Flap shoulder bag. Back and flap (1× leather), Back and flap lining (1× thin leather), Front (1× leather + 1× lining), Gusset (sides and bottom) (1× leather + 1× lining), Inner zip pocket lining (1× lining (folded in half)), Shoulder strap (doubled) (1× leather, doubled), Binding (1× leather 0.6 mm), Strap tabs (2× leather), Closing tab (2× leather (magnet between)).
BagWidthHeightDepth
Classic flap bag23–3016–205–9
Small crossbody22–2513–185–8
Shoulder bag24–3518–289–12
Shopper or tote28–4022–459–12
Briefcaseabout 40about 30about 7
Sports bagabout 53about 35about 22

Measurements in centimetres, as a starting point; every bag in the editor lets you set its own.

Leather goods practice

  • Skive every edge that is folded or turned, and on turned work every seam edge too.
  • Glue before stitching, so nothing moves under the needle and no pins mark the leather.
  • Reinforce where handles and straps pull, with a patch of leather or board inside.
  • Cases and suitcases are built over a rigid frame or a wooden form, with the cover glued to board; they are made to the form rather than drafted.

The bags in the editor

Flap shoulder bagback and flap in one, bound edges, magnet
Soft flap bagturned work, box corners, handles through the flap
Rounded tote with braided handlesshaped panels, tapered gusset, facing
Zip pouch bagsmall crossbody, piped, zip across the top
Soft zip shoulder bagtrapezoid panels, curved zip top, separate bottom
Baguette baglow and long, piped gusset, zip strips, short handle
Hobo bagrounded panels, tapered gusset, facing and zip
Trapeze bagscooped top, box corners, tubular handles
Soft box bagpanels folding round the sides, flat bottom, handle
Bag with cut-out handlehandle shaped from the panel, rings at the sides
Semi-rigid bucket bagfront wrapping round the sides, piped bottom
Fabric shoulder bagfold-over top, box corners, long handle
Edge-stitched shoulder bagsemi-rigid, rounded gusset, raw dyed edges
Rigid top-handle bagrounded panels with darts, arched handles, magnet
Soft gathered sackwide panels, belt through keepers, stadium bottom
Doctor bagdomed ends, zip across the top, tubular handles
Shopper with oval bottomcurved top, facing, magnet closure
Zip-top shopperpiped gusset, zip panel across the top, handles
Structured toteopen top, side gussets, edge-dyed
Dome bagdomed panels, zip round the top, piped bottom
Flat totefabric, turned top, ribbon handles running under the bag
Drawstring bucket bageyelets, leather drawstring, piped bottom
Evening bagfabric, fold-over top with button, box corners
BriefcaseV-shaped flap with lock, side gussets, top handle
Belt bagcurved front and back, zip top, webbing belt
Drawstring backpackflap, front pocket with zip, webbing straps
Two-pocket rucksackfront wrapping round the sides, bellows pockets, flap
Sports bagzip band over the top, webbing handles and strap
Duffle sacktall sack, rounded base, eyelet border and drawcord
Round sailor sackcircular base, eyelets, drawcord, rope straps
Make one

A pattern drafted to your body

Pick a garment, type your measurements and print it at home. The T-shirt and the A-line skirt are free to print, and your first PDF of any other pattern is free.

Choose a pattern
New chapters

Get new patterns and chapters by e-mail

About once a month. We send a link to confirm, which also opens a free account.