The course

Chapter 16

The sheath dress

Every number below follows the size you pick.

The sheath dress is the darted bodice carried down to the hem: fitted at the bust and the waist, close over the hips, with a zip at the back.

The bodice chapter shows the frame, the bust darts and the waist; the straight skirt chapter shows the hip line and the skirt darts. The dress joins both in one piece without a waist seam.

What you need

MeasurementWhere the tape goesSize 38
BustRound the fullest part of the bust, level all round, under the arms. Wear the bra the garment will be worn with.88.0 cm
WaistRound the natural waist, where the body is narrowest, usually just above the navel.72.0 cm
HipRound the fullest part of the hips and seat, feet together.97.0 cm
NeckRound the base of the neck, over the prominent bone at the back and just above the collarbones at the front.36.6 cm
Back length (nape to waist)Down the centre back, from the prominent bone at the base of the neck to the waist. Tie a string round the waist to find it.40.6 cm
Front length (neck point to waist)From the side of the neck, over the bust point, straight down to the waist.45.0 cm
Bust point depthFrom the side of the neck down to the bust point, the fullest point of the bust.27.5 cm
Shoulder to shoulderAcross the back from one shoulder point to the other, over the base of the neck.37.2 cm
Waist to hipDown the side of the body from the waist to the fullest part of the hip or seat.21.0 cm
Arm lengthFrom the shoulder point over a slightly bent elbow to the wrist bone.60.0 cm
BicepRound the fullest part of the upper arm, arm relaxed.28.0 cm

Draft the sheath dress to your measurementsFree to draft, your first PDF free

Front.
Back.

How it is drafted

  • One piece to the hem. Back and front run from the shoulder to the hem, with no seam at the waist; darts shape the bust and the waist.
  • Back zip. The back is cut in two halves with a seam at the centre for the zip; the front is cut on the fold.
  • Facings. The neck and armholes are finished with facings drafted from the same edges, so they lie flat inside.

The finished pieces

BACKFRONTFRONT FACINGBACK FACING
Sheath dress, size 38. Back (2×), Front (1× on fold), Front facing (1× on fold (+ interfacing)), Back facing (2× (+ 2× interfacing)). Seam allowance is added afterwards.

Sewing it

  1. Cut and mark. Cut every piece with the grain arrow parallel to the selvedge. Transfer the notches, the dart points and the marks with tailor's chalk or a short snip into the seam allowance.
  2. Interfacing. Fuse interfacing to the collar, stand, cuffs, waistband, facings and front edges before sewing anything.
  3. Darts. Sew each dart from the wide end to the point, the last stitches right on the fold. Tie the threads at the point, do not backstitch. Press waist darts towards the centre, bust darts downwards.
  4. Shoulders. Sew the shoulder seams, the back eased onto the front. Press open.
  5. Zip. Sew the centre back seam up to the zip mark and insert an invisible zip.
  6. Facings. Sew the facing shoulders and finish the lower edge. Lay the facing on the dress right sides together and sew round the neckline and both armholes. Trim, clip the curves and turn each shoulder through to the right side, pulling the back through the shoulders. Understitch as far as you can, press, and fold the facing ends over the zip tape at the centre back.
  7. Side seams. Open the facing out and sew the side seams of the dress and the facing in one line, from the hem to the end of the facing. Press open and tack the facing down at the seams.
  8. Hem. Turn up the hem twice and stitch, or catch it by hand.
Make it

Draft the sheath dress to your measurements

The editor draws this pattern for your body in a few seconds, with seam allowance, notches and sewing steps. Your first PDF is free.

Open the sheath dress
New chapters

Get new patterns and chapters by e-mail

About once a month. We send a link to confirm, which also opens a free account.